✅ We write about cars and everything about cars plus reviews. Here is detailed information about car brands with photos

How to set the ignition on the VAZ-2109. Recommendations

4

In order to timely ignite the air-fuel mixture in a gasoline internal combustion engine, an ignition system is required. It is she who is responsible for the appearance of a spark between the contacts of the electrodes of the spark plugs at the right time. Converting from a low voltage of the on-board network of 12 V to a higher voltage of up to 30,000 V, the system distributes the spark at a given time to a specific cylinder. A diesel engine does not need such a system, since the principle of ignition of its combustible mixture is based on the compression stroke.

In the article we will try to figure out how to set the ignition on the VAZ-2109. And along the way we will offer a lot of other useful information.

How to set the ignition on the VAZ-2109

How to set the ignition on the VAZ-2109. Recommendations

What is needed for this? Before you set the ignition on the VAZ-2109, you must first visually inspect several nodes that are responsible for the correct operation of the entire engine. These include:

  • spark plug;
  • high voltage ignition coil;
  • capacitor;
  • distributor (ignition distributor);
  • armored lines;
  • interrupter contacts.

After everything has been inspected, the engine is warmed up to an operating temperature of 90 degrees, and then the ignition moment is set. To install it, you need to find the viewing window located on the gearbox housing, open it and combine the mark on the crankshaft flywheel with the scale. Thus, the piston of the first and fourth cylinders should be at top dead center. This can be checked by removing the timing belt guard, or by removing the spark plugs. If the 1st and 4th pistons are at TDC of the cylinder, then the mark on the camshaft pulley will point to the casing mark.

How to set the ignition on the VAZ-2109. Recommendations

When the marks are in the specified place, remove the wire from the breaker going to the ignition coil and connect a 12 V bulb to it. We hook the negative wire of the bulb to the car body. Then we loosen the distributor mounting nuts and turn on the ignition by turning the key in the ignition lock. The light bulb should be on. Slowly rotating the distributor, watch when it goes out. As soon as this happens, we rotate it in the opposite direction and at the moment when the light comes on again, we tighten the nuts. Now you know how to set the ignition on the VAZ-2109.

Ignition check "by ear"

This verification method is not the most accurate, as it requires some experience. You can check the correct installation of the VAZ-2109 ignition by ear both on the injection and on the carburetor engine. After warming up the car and accelerating it to a speed of approximately 50 km / h, you need to turn on 4th gear. Then you need to sharply press the accelerator pedal and listen to the sound of the engine. If characteristic detonation occurs, everything is fine – the ignition is set correctly, and if this does not happen, the ignition moment is late. Detonation may be too strong, this indicates that the ignition is early.

Setting the ignition on the VAZ-2109 using a stroboscope

How to set the ignition on the VAZ-2109. Recommendations

One of the simple ways to install the VAZ-2109 ignition with a carburetor is the stroboscope method. To do this, we take this device, connect it to the on-board network of the car, remove it from the distributor and turn off the octane corrector tube. We set the TDC 1 and 4 of the piston through the hatch located on the gearbox housing and direct the strobe beam to the crankshaft flywheel marks. After that, loosen the three nuts securing the distributor and, slowly rotating it, set the ignition timing depending on the gasoline you use. For the A-92 this angle is 1 degree, and for the A-95 it is 4 degrees.

"Correct" ignition

The key to stable, long and proper operation of the engine is the correct setting of the ignition timing 2109, as well as any other model. Indeed, with the wrong moment, overheating of the engine, an increase in fuel consumption, increased wear of parts, and unstable idling can occur. In addition to the above, the motor will not develop power corresponding to the passport characteristics.

Post source: wekauto.ru

This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish. Accept Read More