Cruise control on the mechanics: installation, advantages

Mechanical cruise control is a system used to maintain a set speed. The system controls the speed limit in the car when it is forced to travel frequently on the motorway or if the driver lives in a country house.

Get to know your device

Cruise control on the mechanics has as its main goal the economy of gasoline and other existing fuels. The system is designed for use on premium cars. After all, the process of movement occurs in such a way that the driver constantly has to change the level of speed, increasing and slowing it down. So it is controlled by the speedometer. These speed fluctuations lead to erratic fuel consumption and constant driver distraction.

System Benefits

Statistics show that using manual cruise control saves fuel by an average of 12%.

In addition, maintaining a constant level of speed protects the parts and mechanisms of cars from rapid wear, which saves consumable fluids. Experts carried out the necessary calculations and found out that it is possible to achieve a reduction in financial costs by 2%. Thanks to the use of modern speed control systems on the mechanics, many additional options can be obtained. Including scanning the free space that opens in front of the car. Thus, the driver can find out if there are any unexpected obstacles in his way.

The lower speed limit indicator is a number between 30 and 50 km/h. The maximum speed limit level will depend on the vehicle manufacturer. Typically, the performance of such a system varies from 200 to 220 km / h. At low speeds, for example, in a traffic jam, the driver can only use the steering wheel. And the function of the system in this case will be to automatically increase and decrease the speed of movement by adjusting the brake pedals and the accelerator handle.

Description of the cruise control scheme

Take, for example, the new Zhiguli, which does not provide for a mechanical speed control system.

The following structural components will control movement speed:

• The control module or control unit is a kind of computer microprocessor located in the engine compartment.
• Electric or pneumatic accelerator drive. This depends on the type of fuel supply system used. This transmission and throttle are connected to each other.
• A switch is a device that has access to the steering wheel, center console, or the area where the control panel is located. The above switch is for arming and disarming the system.
• Controller types. The different number of sensors in this system is explained by the fact that everything depends on the manufacturer and brand. Both high-speed rotation of the wheel and speed control of the rotating wheels and throttle element can be provided.

If a speed control system is installed in the new Lada, then the unit will be integrated into the system responsible for driving a specific vehicle.

Features of work

Installing cruise control on the mechanics for many motorists is considered unrealistic. But with a detailed study of the problem, you can find out that such an installation can be done with your own hands. The main thing is to think about the expediency of such an action. In fact, in addition to the advantages listed above, the cruise control system also has some disadvantages. We will talk about them later.

This feature is designed for automation and is used in most premium models. This is the advantage of an automatic transmission. You can install the system normally. Installation is simple as only the space provided by the vehicle manufacturer is required.

Cruise control can be successfully installed on Lada Vesta if you use a universal device for this purpose.

Expert advice

Do-it-yourself cruise control on the mechanics can be installed with your own hands. This will help the advice of professionals. As mentioned above, a universal device is used for mechanics. It is desirable that it be German, since it is these systems that are of high quality and, according to consumer reviews, are quite reliable. Choosing a quality cruise control system is a guarantee of protection against malfunctions and failures that can be caused by overload. The overload is caused by the vehicle not being fully compatible with the universal cruise control system.

Installation Features

To properly connect the multifunction steering wheel to Lada West, you will also need to install a bracket and a gas cable. This will enable you to check the speed level of the vehicle. Installing cruise control also requires installing a button that controls the device. Located under the deflector. Knowledge of these features is essential for a successful installation.

How to connect the system if the manufacturer did not provide for it

First of all, you must first make sure how good the car’s components are. A good tire must be installed. If these conditions are not met, automatic control of the machine is not possible. If all systems are working, the driver will take care of his safety.

it is important to pay attention to the presence of a sensor that monitors the position of the accelerator pedal. If you have one, you will need to purchase an additional bracket. You can also install it yourself.

Installation steps for the cruise control system

It will take an hour to complete the job. So it is also necessary to check the operation of the system in order to eliminate existing problems. The sequence of work is as follows:

• Select the location where the system will be placed. This is usually a fuel filter, but a brake hose can also be used.
• We connect the second cable and the accelerator. Before cutting it, you need to install a sensor that checks how the accelerator pedal is located. The other end is for connecting the cable to the cruise control.
• Find the cable that connects to the tachometer and connect it to the new device. This wire is also connected to the green wire coming from the control box. The red wire connects to the brake light system.
• a button is installed that is responsible for turning the cruise control system on and off. It uses a double gray thread. Be sure to pull the ground from the black wire.
• Since the steering wheel is required to install the system control knob, it will need to be disassembled. If airbags are present, they must be temporarily removed. After installing the handle, the steering wheel is assembled.
• System performance is checked. To activate cruise control, simply press the button on the device.

Summing up

The article addressed the question of whether it is possible to install cruise control on the mechanics. By its principle, this function is reduced to the ability to automatically maintain a speed level previously set by the driver. And there is no need to use the accelerator pedal.

To activate the cruise control system, the driver simply presses a button on the device. You can immediately feel the possibilities of the system and use it to the fullest.

After pressing the button, it is important not to touch the accelerator pedal with your foot. This ensures uniform vehicle speed. It won’t even change because of the rough road.

In this case, the driver can press the pedal if he overtakes or wants to stop moving.

Modern systems have two buttons: on/off and SET. By double-clicking the latter, you can develop the maximum allowable speed.

But it is also important to note that the installation of such a system is only advisable when driving on country roads that are not overloaded with other cars. For city driving, the installation of the system is useless. After all, the driver still needs to constantly use the brake pedal.